OPERATOR’S MANUALSNOW THROWER MODELSE600E, E610EE640F, E660GE6C0FIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 368
10SECTION 6: ADJUSTMENTSWARNING: NEVER attempt to cleanchute or make any adjustments whileengine is running. Refer to label inFigure 2 in safety se
11Minor carburetor adjustment may be required to com-pensate for differences in fuel, temperature, altitude and load.Refer to the separate engine man
12WHEELSOil or spray lubricant into bearings at wheels at least once a season. Pull the klick pins and remove wheels, clean and coat axles with a mul
13To remove shave plate, remove the carriage bolts, bell washers and hex nuts which attach it to the snow thrower housing. Reassemble new shave plate
14DRIVE BELT1. Follow steps 1 through 4 of previous instruc-tions.2. Pull idler pulley up, and lift belt off engine pulley and friction wheel disc. S
15SECTION 9: OFF-SEASON STORAGEWARNING: Never store engine with fuel in tank indoors or in poorly venti-lated areas, where fuel fumes may reach an o
16NOTES
17REF.NO.PARTNO. DESCRIPTION1 618-0123 RH Reducer Housing2 618-0124 LH Reducer Housing3 710-0642 Hex Screw 1/4-20 x .754 711-0909 Spiral Axle 26"
18Blower HousingModels E600E, E610E, E640F, E660G, and E6C0F123456789101112141513161091819202122231325232226182728133030313231323316183536373839414042
19REF.NO.PARTNO. DESCRIPTION1 712-0116 Lock Jam Nut 3/8-242 756-0178 Flat Idler 3 784-5632A Auger Idler Arm4 710-0459A Hex Cap Screw 3/8-24 x 1.505 73
2SECTION 1: FINDING YOUR MODEL NUMBERThis Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare andmai
20Handle AssemblyModels E600E, E610E, E640F, E660G, and E6C0F37524322452318462542497234551242494556426268101441194075967124030233912201438245845352154
21REF.NO.PARTNO. DESCRIPTION1 625-0007 Light Ass’y, Top Mount2 684-0008A Shift Arm Ass’y.3 684-0022 Chute Crank Ass’y.4 684-0036 Handle Ass’y - Engage
22Frame AssemblyModels E600E, E610E, E640F, E660G, and E6C0F11234455616” Wheels477891010111112151314151617181192021222324252526282926113031323334835Dr
23REF.NO.PARTNO. DESCRIPTION1 710-1652 Hex Screw 2 784-5688 Drive Cable Guide Bracket3 784-5687A Auger Clutch Cable Bracket4 756-0625 Roller Cable5 73
24REF.NO.PARTNO. DESCRIPTION1 710-0599 Hex Washer Screw 1/4-20 x.52 731-1324 Belt Cover3 732-0339 Extension Spring4 710-0627 Hex Screw 5/16-24 x .755
25REF.NO.PARTNO. DESCRIPTION1 710-1652 Hex Washer Screw 1/4-20 x .6252 731-1324 Belt Cover3 732-0710 Extension Spring4 710-0627 Hex Screw 5/16-24 x .7
26
MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTDPRODUCTS INC (“MTD”) with respect to new merchandisepurchased
3SECTION 3: IMPORTANT SAFE OPERATION PRACTICESWARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IFNOT FOLLOWED, COULD ENDANGER TH
4repairs, adjustments, or inspections. Never place your hand in the discharge or collector openings. Use a stick or wooden broom handle to unclog the
5SECTION 4: ASSEMBLYAUGER SHEAR BOLTS (SPARES)NOTE: The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. If you hit a
6Figure 5 FINAL ADJUSTMENTSAuger Control AdjustmentTo check the adjustment of the auger control, push forward on the left hand control, depressing t
7SECTION 5: OPERATIONOPERATING CONTROLSSHIFT LEVER The shift lever is located in the center of the handle panel. The shift lever may be moved into o
8THROTTLE CONTROLThe throttle control is located on the engine. It regu-lates the speed of the engine. See Figure 10.BEFORE STARTINGWARNING: Observe
9Follow all instructions carefully. Determine that your house wiring is a three wire grounded system. Ask a licensed electrician if you are not certa
Comments to this Manuals