MTD OEM-190-821 Operator's Manual download pdf (Page 17)

• Avoid turns when driving on a slope. If a turn must

be made, turn down the slope. Turning up a slope

greatly increases the chance of a roll over.

• Avoid stopping when driving up a slope. If it is

necessary to stop while driving up a slope, start up

smoothly and carefully to reduce the possibility of

flipping the tractor over backward.

Setting The Cruise Control

• Place the shift lever in the FORWARD position,

then slowly depress the drive pedal until the desired

speed is achieved.

• Lightly depress the cruise control button.

• While continuing to hold the cruise button in, lift

your foot from the drive pedal (you should feel the

cruise latch engage).

• Once engaged, the cruise control button and the

drive pedal will lock in the “down” position, and the

tractor will maintain the same forward speed.

NOTE: Cruise control can not be engaged at the

tractor’s fastest ground speed. If the operator should

attempt to do so, the tractor will automatically

decelerate to the fastest optimal mowing ground speed.

Disengage the cruise control using one of the following

methods:

• Depress the brake pedal to disengage the cruise

control and stop the tractor.

• Lightly depress the drive pedal.

To change to the reverse direction when operating with

cruise control, depress the brake pedal to disengage

the cruise control and bring the tractor to a complete

stop. Then place the shift lever in the REVERSE

position and depress the drive pedal.

Engaging the Blades

Engaging the PTO (Blade Engage) transfers power to

the cutting deck or other (separately available)

attachments. To engage the blades, proceed as

follows:

• Move the throttle control lever to the FAST (rabbit)

position.

• Grasp the PTO (Blade Engage) lever and pivot it all

the way forward into the engaged (ON) position.

• Keep the throttle lever in the FAST (rabbit) position

for the most efficient use of the cutting deck or other

(separately available) attachments.

IMPORTANT:

The engine will automatically shut off if the

PTO is engaged with the shift lever in position for

reverse travel with the ignition key in the NORMAL

MOWING position. Refer to Safety Interlock Switches on

page 15.

Using the Deck Lift Lever

To raise the cutting deck, move the deck lift lever to the

left, then place it in the notch best suited for your

application. Refer to Setting The Cutting Height earlier in

this section.

Mowing

WARNING: To help avoid blade contact or

a thrown object injury, keep bystanders,

helpers, children and pets at least 75 feet

from the machine while it is in operation. Stop

machine if anyone enters the area.

The following information will be helpful when using the

cutting deck with your tractor.

WARNING: Plan your mowing pattern to

avoid discharge of materials toward roads,

sidewalks, bystanders and the like. Also,

avoid discharging material against a wall or

obstruction which may cause discharged

material to ricochet back toward the operator.

• Do not mow at high ground speed, especially if a

mulch kit or grass collector is installed.

• For best results it is recommended that the first two

laps be cut with the discharge thrown towards the

center. After the first two laps, reverse the direction

to throw the discharge to the outside for the

balance of cutting. This will give a better

appearance to the lawn.

• Do not cut the grass too short. Short grass invites

weed growth and yellows quickly in dry weather.

• Mowing should always be done with the engine at

full throttle.

• Under heavier conditions it may be necessary to go

back over the cut area a second time to get a clean

cut.

• Do NOT attempt to mow heavy brush and weeds

and extremely tall grass. Your tractor is designed to

mow lawns, NOT clear brush.

• Keep the blades sharp and replace the blades

when worn. Refer to Cutting Blades on page 24 of this

manual for proper blade sharpening instructions.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 51 52

Comments to this Manuals

No comments

MTD OEM-190-821 Operator's Manual Page 17

Comments to this Manuals

Related products and manuals for Lawnmowers MTD OEM-190-821