IMPORTANT READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722Model Series800Snow ThrowerPRINTED
10 SHIFT ROD ADJUSTMENT To adjust the shift rod, remove the cotter pin whichsecures the shift rod to the shift lever. For properadjustment, refer to
11SECTION 9: MAINTENANCEWARNING: Disconnect the sparkplug wire and ground against theengine before performing any repairsor maintenance.AUGERSThe au
12Figure 17 Figure 18 Figure 19 8. Separate the auger housing from the frameassembly by tilting the housing forward andpulling up the handles. To
13Changing the Friction WheelThe rubber on the friction wheel is subject to wearand should be checked after 25 hours of operation,and periodically th
14SECTION 11: TROUBLE SHOOTING GUIDENote: For repairs beyond the minor adjustments above, contact your local authorized service dealer.Trouble Possi
15SECTION 12: ILLUSTRATED PARTSHeadlight PanelRef. No.Part No. Description Qty.1 710-0351 Pan Head B-Tapp Screw #10 22 710-0451 Carriage Bolt 5/16-
16Handle Assembly2829303132333435363738394041434445464748495051525354555657585960616263646566676834353538394042696969
17Handle AssemblyRef. No.Part No. Description Qty.1 749-0991 Handle Lower 12 749-0990A Handle Upper RH 13 749-0989A Handle Upper LH 15 711-0677 Adjust
18Auger Housing
19Auger HousingRef. No.Part No. Description Qty.1 736-0159 Flat Washer .344 ID x .875 OD 72 710-3015 Truss. Hd. Mach. Scr. 1/4-20 x .75 64 736-0105 Be
2SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IFNOT FOLLOWED, COULD ENDANGER T
20Engine and V-Belts
21Engine and V-BeltsRef. No.Part No. Description Qty.1 629-0071 Extension Cord 10 Ft. 12 710-0502A Hex L-wash Tt Scr 3/8-16 X 1.25 43 710-0607 Hwhd 5/
22Transmission
23TransmissionRef. No.Part No. Description Qty.1 05523 Pivot Axle Brkt. .63 Hole - Zinc 13 618-0279 Dogg Asm Dr Lh 15 618-0294 Shf Asm Dr 16 618
MANUFACTURER’S LIMITED WARRANTY FOR:For TWO YEARS from the date of retail purchasewithin the United States of America, its possessionsand territories,
3• If the snow thrower should start to vibrateabnormally, stop the engine and checkimmediately for the cause. Vibration is generally awarning of tro
4 SECTION 2: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and
5 SECTION 4: SET-UP INSTRUCTIONS Figure 3 Figure 4 Figure 5 NOTE: Reference to right or left side of the snowthrower is from behind the unit i
6 Figure 6 Figure 7 Figure 8 FINAL ADJUSTMENTSAuger and Traction Drive Clutch Adjustment To check the adjustment of either drive clutch, pushfor
7 SECTION 5: CONTROLS Figure 9 SHIFT LEVER (See Figure 9)The shift lever is located in the center ofthe handle panel. The shift lever may bemove
8 SECTION 6: OPERATION NOTE: This unit has been shipped with oil in theengine. Check oil before starting engine. GAS AND OIL FILL-UP Check oil lev
9 TO STOP ENGINE 1. Run engine for a few minutes before stopping tohelp dry off any moisture on the engine. 2. To help prevent possible freeze-up of
Comments to this Manuals