IMPORTANT: Read safety rules and instructions carefully before operating equipment.MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722Snow Th
10Chute Tilt ControlThe distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Move the chute tilt control forward to d
11• When disconnecting the power cord, always unplug from the three-prong receptacle first, and then from the snow thrower.Recoil Starter• Rotate chok
12SECTION 5: MAKING ADJUSTMENTSWARNING: NEVER attempt to cleanchute or make any adjustments while engineis running.Chute Assembly The distance snow
13Drive WheelsThe wheels may be adjusted for two different methods of operation. The adjustment is made by placing the click pins in one of two differ
14operation, remove rear cover. Lubricate any chains, sprockets, gears, bearings, shafts, and shifting mechanism at least once a season. Use engine oi
15Figure 21• Unhook the idler spring from the hex bolt on the auger housing. See Figure 22.• Back out the stop bolt until the support bracket rests on
16Figure 24• Lightly tap the hex nut to dislodge the ball bearing from the right side of frame before removing the hex nut and bell washer from left e
17SECTION 9: TROUBLESHOOTINGProblem Cause RemedyEngine fails to start1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Choke not in ON positi
18SECTION 10: PARTS LIST FOR MODELS E633 AND E663212171513325221416923292412628187122062115AA54181129919101220443532484535323344454649327236385132114
19Models E633 and E663Ref. No.Part No. Part Description1.684-0008A Shift Arm Assembly2.684-0053A705-5204ALower Chute Crank (E663)Chute Crank Ass’y (E
2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Assembling Your Sn
20Models E633 and E6638273340222920283833627396271035292228235142110131542511832331112019378302131724361273486(Drive Clutch Cable)NOTE: Axle goes here
21Models E633 and E663Ref. No. Part No. Part Description1.656-0021A Friction Wheel Disc Assembly2.684-0013B Shift Rod Assembly3.684-0021 Support Bra
22Models E633 and E66312345678910111214151316109 1819202122231325232226182728133030313231323316183534363738394140421740392924
23Models E633 and E663Ref. No. Part No. Part Description1.712-0116 Lock Jam Nut 3/8-242.756-0178 Flat Idler 3.784-5632A Auger Idler Arm4.710-0459A Hex
24Model E633123456748910111213141516171819202122232425262728Ref. No. Part No. Part Description1.710-0599 Hex Washer Screw 1/4-20 x.52.731-1324 Belt Co
25Model E66323456748910111213151416171819201616212223242526271Ref. No. Part No. Part Description1.710-0599 Hex Washer Screw 1/4-20 x .502.731-1324 Bel
26Model E633
27Model E663
MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTDPRODUCTS INC (“MTD”) with respect to new merchandisepurchased
3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis symbol points out important safety instructions which, if not followed, could endanger the persona
4chute. Keep all safety devices in place and working.5. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon mon
5SECTION 2: ASSEMBLING YOUR SNOW THROWERUnpacking• Remove screws from the top sides and ends of the shipping crate.• Set panel aside to avoid tire pu
6• Secure the upper handle and lower handle with the two plastic wing nuts, cupped washers and carriage bolts previously removed. Attach these hardwar
7If the spiral on the chute directional control cannnot be adjusted properly, follow the steps below:• Loosen the two hex nuts which secure the chute
8• Release the auger control. The cable should be straight. Make certain you can depress the auger control against the left handle completely.• If adj
9SECTION 3: KNOW YOUR SNOW THROWERWARNING: Be familiar with all the controls and their proper operation. Know how to stop the machineand disengage th
Comments to this Manuals