Mtd 240-610-000 User Manual

Browse online or download User Manual for Tools Mtd 240-610-000. MTD 240-610-000 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 16
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
$1.00
owiers GUIDE
ASSEMBLY • OPERATION • MAINTENANCE • PARTS
S
13 TON Model Number
HORIZONTAL 240-610-000
LOG SPLITTER
Important: Read Safety Rules and Instructions Carefully
2:
PRINTED IN U.S.A.
FORM NO. 770-6744E
Page view 0
1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - LOG SPLITTER

$1.00owiers GUIDEASSEMBLY • OPERATION • MAINTENANCE • PARTSS13 TON Model NumberHORIZONTAL 240-610-000LOG SPLITTERImportant: Read Safety Rules and Ins

Page 2 - IMPORTANT

NOTEA DIRTY AIR CLEANER WILL CAUSE ENGINE TO RUN ROUGH. BE CERTAIN AIR CLEANER IS CLEAN AND ATTACHED TO THE CARBURETOR BEFORE ADJUSTING CARBU

Page 3 - MAINTENANCE

Trouble Shooting GuideNTroublePossible Cause(s)Corrective ActionEngine fails to start1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Spar

Page 4 - ASSEMBLY

Model 610NOTESpecifications subject to change without notice or obligation.T0TA.L CftPAClTY 3 GALLONSDEXRONTt AUTOMATIC TRANS. FLU\D12

Page 5

Model 610NPARTS LIST FOR MODEL 610 LOG SPLITTERREF.NO.PARTNO.CODEDESCRIPTIONREF.NO.PARTNO.CODEDESCRIPTION1 781-0038Wedge Ass’y-39 712-0338Hex Nut 1-1/

Page 8 - A I* WA*R*N*NG*J

parts; informationPOWER EQUIPMENT PARTS AND SERVICE BRIGGS AND STRATTON, TECUMSEH AND PEERLESS PARTS ANQParts and service are available through the a

Page 9 - \ WARNING j

IMPORTANTRULES FOR SAFE OPERATIONATHIS SYMBOL POINTS OUT IMPORTANT SAFETY INS FRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND

Page 10 - Ai WARNING^

2. Know how to stop the unit and disengage the controls.3. Never place hands or feet between log and splitting wedge or between log and ram dur

Page 11 - Trouble Shooting Guide

IMPORTANTThis unit has been shipped withoui gasoline or oil in the engine. Aftei assembly, refer to separate engine manual for proper

Page 12 - 3 GALLONS

LockINSTALLATION OF WHEELS1. Using a flat blade screwdriver, pry off the hub caps which are attached to the wheels. Remove one tapered roller bear

Page 13 - Vi" NPT x 2" Lg

Clevis Pin Cotter Pin2.Place the hitch in position on the beam stand as shown in figure 6. Piace spacer (L) inside the beam stand. Insert hex bolt (K)

Page 14

d. Stop the engine. Remove the fluid check plug. Add fluid as necessary until fluid starts to come out of the hole. Replace the check plug.e. Repeat

Page 15

voir tank before each use. Refer to under Operation Section.‘Before Starting”TO OPERATE LOG SPUTTER:1. Set throttle at maximum speed.2. Place log on

Page 16 - MTD PRODUCTS INC

BEAM AND SPLITTING WEDGELubricate the beam where it contacts the ram with grease before each use to obtain years of service.HOSE CLAMPSCheck t

Comments to this Manuals

No comments