Mtd E640F User Manual

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722SNOW THROWERS ModelsE600E, E610EE

10 Traction Drive Clutch and Shift Lever Adjustment To check the adjustment of the traction drive clutchand shift lever, move the shift lever all th

11 TRACTION DRIVE/AUGER CLUTCH LOCK (See Figure 14) The traction drive clutch is located on the right handle.Squeeze the traction drive clutch to en

12 Electric Starter: WARNING: The electric starter isequipped with a three-wire power cordand plug, and is designed to operate on120 volt AC househ

135. Wipe all snow and moisture from the carburetorcover in the area of the control levers. Also,move control levers back and forth severaltimes.TO E

14SKID SHOE ADJUSTMENTThe space between the shave plate and the groundcan be adjusted. Refer to page 10 of the AssemblyInstructions.TRACTION DRIVE CL

15WHEELSOil or spray lubricant into bearings at wheels atleast once a season. Pull the klick pins and removewheels, clean and coat axles with a multi

16BELT REMOVAL AND REPLACEMENTWARNING: Disconnect the spark plug wire from the spark plug and ground. AUGER BELTSNOTE: It is necessary to remove bo

17Figure 28 CHANGING FRICTION WHEEL RUBBERThe rubber on the friction wheel is subject to wear andshould be checked after 25 hours of operation, andp

18SECTION 12: Trouble Shooting GuideNote: For repairs beyond the minor adjustments above, contact your local authorized service dealer.Trouble Possi

19REF.NO.PARTNO. DESCRIPTION Qty.1 618-0123 Housing—L.H. 12 618-0124 Housing—R.H. 13 710-0642 Screw 54 711-0908 Spiral Axle 24" 1711-0909 Spiral

2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IFNOT FOLLOWED, COULD ENDANGE

20Blower HousingE600EE610EE640FE660G

21Blower HousingE600EE610EE640FE660GREF.NO.PARTNO. DESCRIPTION QTY.1 784-5618 Housing, Bearing 22 05931 Housing, Bearing 13 618-0120 Gear Assembly (2

22Handle AssemblyE600EE610EE640FE660G

23Handle AssemblyE600EE610EE640FE660GREF.NO.PARTNO. DESCRIPTION QTY.1 684-0008A Arm-Shift 13 684-0033A Panel-Handle 14 684-0036 Handle-Engagement—R.H.

24Frame AssemblyE600EE610EE640FE660G

25Frame AssemblyE600EE610EE640FE660GREF.NO.PARTNO. DESCRIPTION QTY.1 618-0063 Bearing Ass’y. 12 656-0012A Ass’y., Friction Wheel Disc 13 684-0013B Rod

26REF.NO.PARTNO. DESCRIPTION QTY.1 05896A Bracket-Idler 12 629-0071 Cord-Extension 110V 13 710-0627 Screw-Hex 14 710-1245 Screw-Hex 15 710-0230 Screw

27Engine and V-BeltsE640FE660G16 736-0270 Washer—Lock 117 736-0331 Washer—Bell 118 736-0505 Washer—Flat 119 748-0234 Shoulder Spacer 120 748-0360 Pul

MANUFACTURER’S LIMITED WARRANTY FOR:For TWO YEARS from the date of retail purchasewithin the United States of America, its possessionsand territories,

3 • If the snow thrower should start to vibrateabnormally, stop the engine and checkimmediately for the cause. Vibration is generally awarning of tr

4 SECTION 2: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepareand

5 SECTION 4: CONTENTS OF HARDWARE PACK Lay out the hardware according to the illustration for identification purposes. Part numbers are shown in par

6 SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: After assembly, service engine withgasoline, and check oil level as instructed in theseparate engine

7 Figure 4 Figure 5 Figure 6 ATTACHING THE HANDLE ASSEMBLY(Hardware A) 1. Place right handle (A) in position against thesnow thrower so the flat

8 Figure 7 Figure 8 Figure 9 Figure 10 ATTACHING THE CHUTE ASSEMBLY (Hardware B) Place chute assembly (C) over chute opening, withthe opening i

9 Figure 11 Figure 12 IMPORTANT : Attach the shift rod and clutch cablesas follows. THEN CHECK THE ADJUSTMENTS ASINSTRUCTED, AND MAKE ANY FINAL