MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USA
NOTE: This Operat
Starting the EngineRead, understand and follow all instructions and warnings on the machine and in this manual before operating. We
Stand in front of the log splitter to operate the c. control handle and to stabilize the log. See Fig. 5-2.To place the beam in the Horizontal Positi
Secure with the spring clip and clevis pin previously 4. removed. See Fig. 5-5.Attach the coupler hitch to a class I or higher 2” ball on a 5. towing
Do not make any adjustments without first stopping the engine, disconnecting the spark plug wire and grounding it against the engine. Always
Refill the reservoir within range marked on the dipstick. 9. See Fig. 6-2.Extend and retract the wedge 12 complete cycles to 10. remove trapped air in
Wedge AssemblyAs normal wear occurs and there is excessive “play” between the wedge and beam, adjust the bolts on the side of the wedge assembly to el
Notes
Problem Cause RemedyEngine fails to start Spark plug wire disconnected.1. Fuel tank empty or stale fuel.2. Choke not in CHOKE position.3. Faulty spark
Problem Cause RemedySlow cylinder shaft speed while extending and retractingGear sections damaged.1. Excessive pump inlet vacuum. 2. Slow engine spee
Customer SupportPlease do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.If you have diffic
20BAACCDBDAABCBCDD25248281376711431164210924272625232829313435 563046444740172019334040434140413845373739366137586948664249245559662463626867298078767
21se c t i O n 12 — il l u s t r a t e d pa r t s li s t Description1 711- 0 458 5 Clevis Pin, .25 x 1.002 913-04036 Handle Valve Li
22 Description67 727-0502 Rubber Hydro Hose68 737-0329 Hydraulic Fitting, 45 x ⁄ x ⁄69 737-04093 Inlet Filter70 781-0097-0637 Rear
Notes923
MANUFACTURER’S LIMITED WARRANTY FORGDOC-100015 REV. BThe limited warranty set forth below is given by MTD LLC with respect to new merchandise purchase
Impreso en Estados Unidos de AméricaMa n u a l d e l Op e r a d O r
Asistencia al ClientePor favor, NO devuelva la máquina al minorista o distribuidor sin ponerse en contacto primero con el Departamento de Asistencia a
Medidas importantes de seguridad23CapacitaciónLea, entienda y cumpla todas las instrucciones incluidas en 1. la máquina y en el(los) manual(es) antes
4 se c t i O n 2 — Me d i d a s i M p O r t a n t e s d e s e g u r i d a dEsta máquina se debe utilizar únicamente para cortar 14. madera, no la
se c t i O n 2 — Me d i d a s i M p O r t a n t e s d e s e g u r i d a dEn el caso de troncos que no están cortados en escuadra, 11. el extremo
Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to
6 se c t i O n 2 — Me d i d a s i M p O r t a n t e s d e s e g u r i d a dSímbolos De SeguridadEsta página representa y describe los símbolos de
NOTA: Este Manual del operador se extiende a varios modelos. Registrarse separador características pueden variar según el modelo. No todas las funcion
Conexión del cilindro a la viguetaLa máquina rompe troncos se envía con la vigueta en posición vertical.Tire hacia afuera del bloqueo de vigueta verti
Instalación de luz de cola (si corresponde)Las abrazaderas de montaje de la cola de luz están instalados. Consulte la hoja de instalación incluido con
troncos
Encendido del motorLea, comprenda y siga todas las instrucciones y advertencias que aparecen en la máquina y en este manual antes de op
Párese delante de la unidad para operar la manija de c. control y estabilizar la madera. Vea la Fig. 5-2.Para colocar la vigueta en la posición vertic
Baje la vigueta a la posición horizontal. Asegúrese de que 1. la vigueta esté trabada firmemente con el bloqueo de vigueta horizontal.Retire la abraz
Siempre detenga el motor, desconecte el cable de la bujía y haga masa contra el motor antes de realizar cualquier ajuste. Utilice siemp
AjustesAjuste del retenedorPeriódicamente retire y cambie los “retenedores” (separadores) entre el montaje de la cuña y el contraplato.NOTA: Los reten
4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sThis machine should be used for splitting wood only, do 14. not use it
Para bajar la vigueta:Tire del bloqueo de vigueta vertical sobre el tanque de 1. depósito.Gire el bloqueo de vigueta hacia abajo para liberar la 2. vi
Problema Causa SoluciónEl motor no arranca Se ha desconectado el cable de la bujía.1. El depósito de combustible está vacío o el 2. combustible se ha
Problema Causa SoluciónVelocidad lenta del eje del cilindro durante la extensión o retracción.Hay partes de los engranajes dañadas.1. Vacío excesivo e
Notas919
GARANTÍA LIMITADA DEL FABRICANTE PARAGDOC-100015 REV. BLa siguiente garantía limitada es otorgada por MTD LLC con respecto a nuevos productos adquirid
se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sKeep your work area clean. Immediately remove split wood 13. around the
6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may
Contents of CartonOne Log Splitter• One Tongue Assembly• One Operator’s Manual• One Engine Operator’s Manual• One Tail Light Kit (If equipped)• NOT
Connecting Cylinder to BeamThe log splitter is shipped with the beam in the vertical position.Pull out the vertical beam lock, rotate it back, and piv
Tail Light Installation (If equipped)The mounting brackets for the tail light are installed. Refer to the installation sheet included with the tail li
Comments to this Manuals