MTD 463 User Manual Page 324
- Page / 412
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
TM 5-6115-465-34
NAVFAC P-8-625-34
T.O. 35C2-3-446-2
TM 06858B/06859D-34
b.
Cleaning, Inspection, and Repair.
(1) Clean all parts in dry cleaning solvent
(Federal Specification P-D-680) and dry thorough-
ly.
(2) Inspect supports, lifting clevises and
brackets for cracks, corrosion, breaks, defective
paint, and other damage.
(3) Inspect lifting clevises, brackets, and
pins for excessive wear.
(4) Check all threads for crossing, stripping,
and other damage.
(5) Repair cracks and breaks in supports by
welding.
(6) Remove corrosion and defective paint.
Treat and paint in accordance with service require-
ments.
(7) Replace all parts worn or damaged beyond
repair.
c. Installation.
(1) Install lifting frame in reverse order of
removal procedures.
(2) Install the housing assembly doors,
covers, and panels, the hydraulic sump, the fuel
lines and fittings, the day tank assembly, and the
main fuel tank filler neck removed in steps a. (1)
through a. (4) above.
Section III.
SKID BASE ASSEMBLY
6-5.
GENERAL.
The skid base assembly provides the mounting
points for the engine assembly, the generator as-
sembly, and the enclosure assembly. It contains the
main fuel tank and the tool box. The generator set
ground point is also contained in the skid base as-
sembly. The skid base is also drilled to accept
attachment of the wheel mounting kit. A metal sheet
near the bottom of the skid base prevents the entry
of debris. Drain holes are provided to prevent the
accumulation of spilled liquids on the sheet.
6-6.
SKID BASE ASSEMBLY MAINTENANCE.
a.
Removal.
(1) Refer to the Operator and Organizational
Maintenance Manual and remove the housing assem-
bly.
(2) Remove
graph 6-2).
(3) Remove
(4) Remove
2-7).
(5) Remove
(6) Remove
the relay table assembly (para-
engine assembly (paragraph 2-6).
generator assembly (paragraph
main fuel tank (paragraph 3- 15).
the lifting frame (paragraph 6-4).
b. Disassembly, Disassemble skid base as-
sembly by following the ascending sequence of index
numbers (1 through 12) assigned to figure 6-3.
NOTE
It is not necessary to completely disassem-
ble the skid base assembly to replace a
single part. Only those parts requiring re-
pair or replacement need be removed.
c.
Cleaning, Inspection, and Repair.
(1) Clean all parts with dry cleaning solvent
(Federal Specification P-D-680) and dry thoroughly.
If necessary, use a stiff bristle brush to remove
caked deposits.
(2) Visually inspect skid base for cracks,
corrosion, defective paint and defective welds.
(3) Inspect tool box for cracks, corrosion,
damaged latch and hinge, and defective paint. Replace
tool box if damaged beyond repair.
(4) Inspect ground terminal stud for burns,
corrosion, damaged threads or other damage. Re-
place if defects are noted.
(5) Repair cracks and defective welds in skid
base by welding. File repairs to provide a smooth
finish.
(6) Remove corrosion and defective paint.
Treat and repaint in accordance with service require-
ments.
NOTE
Clean paint from ground terminal stud
mounting to provide effective ground.
6-4
- TECHNICAL MANUAL 1
- DISTRIBUTION: 6
- H. E. REESE 14
- Official: 16
- Table 2-1 56
- 2-2 Change 8 56
- TG35C2-3-446-2 58
- 2-2.2 Change 8 58
- Change 8 59
- 2-2.3 /(2-2.4 blank) 59
- 2-4 Change 5 62
- TO 35C2-3446-2 68
- Figure 2-2 70
- Change 2 71
- 2-11/(2-12 blank) 71
- M 06858B/06859D-34 77
- NAVPAC P-8-625-34 86
- US. GOVERNMENT 88
- PRINTING OFFICE : 88
- Figure 3-12 94
- Field Current Test 94
- TM5-6115-465-34 101
- NAVFAC P-8-625-34 101
- 35C2-3-446-2 101
- TM 06858B/06859D-34 101
- Change 9 102
- Figure 3-18 106
- Figure 3-24 122
- 0w level 127
- Figure 3-33 134
- TM 06858B/06859D-34 138
- ME 56115-46534/3.36 (2) 140
- ACTUATOR STYLES 144
- TM 5-6115-465-34 151
- TO 35C2-3-446-2 151
- Shafts (18) and bushings (19) 153
- Change 1 3-69 155
- TM 5-6115465-34 157
- Figure 4-1 167
- TO 35 C2-3446-2 168
- TO35C2-3-446-2 170
- T035C2-3-446-2 174
- TM 5-6115-465-S4 187
- TO 35C2-3-S-446-2 187
- TM 088S8B/06859D-S4 187
- TM 068 S8B/06859D-34 192
- 4-26 Change 5 192
- TM 06858B/0685WY34 193
- Figure 4-16 194
- Figure 4-17 195
- NAVFAC P-8-625-.34 199
- TM06858B/06859D-34 199
- Change 5 205
- Figure 4-30.1 212
- Figure 4-30.2 215
- Figure 4-30.3 216
- Figure 4-30.4 217
- Figure 4-32 221
- Figure 4-33 222
- Drawing No. 72-2282 222
- Figure 4-34 225
- RELAY ASSEMBLY TO PRECISE 229
- RELAY ASSEMBLY WRING HARNESS 229
- NAVFAC P-8625-34 230
- Tm 06858B/06859D-34 230
- Figure 5-1 234
- Figure 5-5 240
- ME5-6115-465-34/5-7A(3) 248
- Volts ac 258
- NAVFACP-8-625-34 260
- TM06858B//06859D-34 260
- 5-24 Change 4 260
- 5-30 Change 2 268
- T. O. 35C2-3-446-2 287
- ME5-6115-465-34/5-33(2) 289
- Change 2 5-51 289
- Z and the 50/60 297
- 5-60 Change 9 298
- Figure 5-41 302
- Figure 5-43 307
- Figure 5-44 308
- Figure 5-45 309
- Figure 5-46 311
- (Sheet 1 of 2) 311
- Figure 5-47 313
- Figure 6-1 320
- Figure 6-2 323
- Lifting Frame, Exploded View 323
- Change 2 6-3 323
- T.O. 35C2-3-446-2 324
- Ong term (4 hours) 334
- T0 35C2-3-446-2 338
- TM 06858B/08859D-34 338
- Figure 8-1 350
- Figure 8-3 352
- ME 5-61 15-465-34/8-3 (2) 353
- Figure 8-5 356
- Fuel Burning Winterization 356
- Kit Wiring Harness 356
- Drawing No. 72-2856 356
- Drawing No. 72-2875 357
- Figure 8-7 360
- ME 5-6115-465-34/8-9(1) 363
- ME 5-6115-465-34/8-11 366
- Figure 8-13 369
- ME 5-6115-465-34/8-15 373
- Figure 8-15 373
- Figure 8-16 374
- Control B 374
- Figure 8-18 377
- Figure 8-19 379
- Figure 8-20 381
- Figure 8-21 383
- Figure 8-22 384
- O not tighten capscrews 387
- U.S. GOVERNMENT 401
- PIN: 013547-000 412
Related products and manuals for Garden shredders MTD 463
Garden shredders MTD 464 Operations Instructions
(493 pages)
(493 pages)
Garden shredders MTD 460 Series User Manual
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 1.605 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals