Operating Instructions English
5
Fill with fuel only when the engine
has been switched OFF and has
cooled down. Avoid naked flames
and sparking, and do not smoke.
Fuel the appliance outdoors only.
Do not start the engine when fuel has
spilt. Remove the appliance from the
surface soiled with fuel and wait
until the fuel vapours have
evaporated.
To avoid fire hazard, please keep the
following parts free of grass and
escaping oil:
-
engine
-
exhaust
-
battery
-
fuel tank.
Risk of tripping.
Operate the vehicle at walking speed
only.
Caution!
Prevent damage to the appliance
Stones, scattered branches, and
similar objects can damage the
machine and impair its correct
operation. Remove all objects from
the appliance’s path before every
use.
Operate the appliance only when it is
in good technical condition. Subject
the appliance to a thorough visual
check before using it. In particular,
check that the safety devices,
controls, and screw unions are
correctly installed and do not exhibit
any damage.
Replace any damaged parts before
using the appliance.
Operating times
Observe the national or bylaws
for the times you may operate the
appliance. You may have to consult
your local authority.
Check the fuel and oil levels
Note: See also the provided
operating instructions for the engine.
Engine oil: The appliance should be
filled with oil on delivery. Please
check and, if necessary, top up the
oil level.
Fuel: Fuel the appliance as specified
in the operating instructions for the
engine. Never fill the tank to the rim,
but no higher than 1 cm below the
filler neck’s bottom edge.
Check the air pressure
Check the tyres against the
specifications on their walls (approx.
1–1.3 bar), if necessary correcting
the pressure (both tyres should be
equally pressurised).
Adjustment work
Danger!
Never make adjustments when the
engine is running.
‚" Switch OFF the engine,
disconnect the spark plug
terminal, and wait until the
engine has cooled down.
Controls
Symbols
The symbols found on the controls
include the following:
Lever for the safety lock system
Figures 9 and 10
The lever (A) must always be
pressed before either the cutter drive
or the appliance’s drive controls are
switched ON.
Note: The lever must be released
before the engine can be started.
Switching ON (position 2):
‚" Press the lever, and keep it
pressed. This disengages the rear
wheel brake. The wheels can
now turn, and the separate drive
for the cutters can now be
activated.
Switching OFF (position 1):
‚" Release the lever. The rear
wheels are braked automatically
and come to an abrupt stop.
Also, the drive for the cutters is
deactivated and the cutter brake
engaged , stopping the cutters
completely in three seconds.
Danger!
This function must be ensured at all
times and checked before every use
(see the section “Operating the
appliance”). Should this function
not activate, the appliance must
not be used. In this event contact
a specialist garage.
Lever for activating the cutters
Figures 9 and 10
The lever (B) activates the drive for
the cutters.
Switching ON
To activate the cutters, first press the
lever (A) for the safety lock system.
Now push forward the lever (B) for
the cutter drive against the resistance
from the tension spring until the
lever remains in this position.
Switching OFF
Stop the cutters by releasing the lever
for the safety lock system (A).
This switches OFF the cutter drive
(B) and automatically engages the
cutter brake.
Note: The cutter drive must be
deactivated before the engine starts.
Otherwise, the cutters will also start
to rotate.
switched ON
switched OFF
(232 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals