Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • WarrantyWarning: This unit is equipped with an i
10Setting The DepthTilling depth is controlled by the depth stake which can be adjusted to five different settings. Adjust the side shields as you adj
11To adjust the depth stake, remove the clevis pin and hairpin clip. Move the depth stake to the desired setting and secure with the clevis pin and ha
12Cleaning Tine AreaClean the underside of the tine shield after each use. The dirt washes off the tines easier if rinsed off im-mediately instead of
138• Remove the belt keeper bracket located behind the engine pulley by removing two hex bolts and lock washers. See Figure 8-1.• Remove belt and re
1452132935165335164631281245171744366333152753643420402113418104223722368473237502510924365134452641363516291949443314351621428351614114814
159Illustrated Parts ListModel 450 SeriesTo order replacement parts, contact 1 (800) 800-7310 or visit www.mtdproducts.com Ref. Part No. Part Descrip
1620188231016061376225342764303963263236333129662641303024283540264944505951655355565457584446424911166314719517260611215123821226770706869272671
179Illustrated Parts ListModel 450 SeriesTo order replacement parts, contact 1 (800) 800-7310 or visit www.mtdproducts.com Ref. Part No. Part Descrip
18333538373424741316151321251411124862753920313229Wheel shaft shownfor reference only3618122643421728409
199Illustrated Parts ListModel 450 SeriesTo order replacement parts, contact 1 (800) 800-7310 or visit www.mtdproducts.com Ref. Part No. Part Descrip
2Finding and Recording Model NumberModel Number Serial NumberPlease do NOT return the unit to the retailer from which it was purchased, without first
20For repairs beyond the minor adjust-ments listed here, contact an authorized service dealer. 10Trouble ShootingCauseProblem RemedyEngine fails to st
21For parts and/or accessories please call 1-800-800-7310, or 1-330-220-4683.www.mtdproducts.comNOTES:Use this page to make notes and write down impor
22For parts and/or accessories please call 1-800-800-7310, or 1-330-220-4683.www.mtdproducts.comNOTES:Use this page to make notes and write down impor
23For parts and/or accessories please call 1-800-800-7310, or 1-330-220-4683.www.mtdproducts.comNOTES:Use this page to make notes and write down impor
The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its possessions and
31Safety LabelsWARNINGThis symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property
42Safe Operation PracticesWARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State
52Safe Operation PracticesWARNINGThis symbol points out important safety in-structions which, if not followed, could endanger the personal safety and
6NOTE: References to right or left side of the tiller are determined from behind the unit in the operating position.To Remove Unit From Carton• Remo
73Assembling Your TillerWARNINGDo not put your fingers under the belt cover.Maximum tire pressure under any circumstances is 30 p.s.i. Equal tire pre
8Gear Selection HandleThe gear selection handle is located in the center of the handle on the tiller. It is used to select NEUTRAL, REVERSE, or one of
94Know Your TillerWARNINGClutch Control The clutch control is located beneath the handle. Squeezing the clutch control against the handle engages th
Comments to this Manuals